Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser makes use of cutting-edge technology to prevent car theft. This hidden device is not detected by thieves, and it only starts your engine after a PIN number or app is entered.
It connects to the CAN data network of your vehicle and is weatherproof. It has a service/valet function that lets you temporarily start your vehicle when it is in the garage.
Easy to install
The Ghost immobiliser shields your car from theft of keys, cloning and hacking. It uses a PIN code system that is integrated into your vehicle's electronic control unit, making it impossible for thieves to identify. It's not visible and does not require any sensors or special keys. It's also less expensive than replacing an ECU or installing a key fob. It can even lower the cost of insurance.
Follow the instructions of the manufacturer when installing follow the manufacturer's instructions when installing a Ghost 2 vehicle immobiliser. This will ensure that the device operates correctly and effectively. Once the installation is complete check the system by entering the PIN code, then turning on the engine. Regular testing will enable you to identify any problems in the early stages.
Before you begin the installation, ensure the exact location of the CAN H and L wires. They are vital to powering the immobiliser, so it is important to ensure that they are connected correctly. Labelling the wires will aid in locating them when installing. Once you've identified the location of these wires, connect them to a continuous 12V power source as well as the grounding point. Use a fuse tap to protect the connections against short-circuits or damage.
After connecting the wires, neaten the wiring using cable ties to prevent potential alteration. You can also cover the connections with insulation tape or heat-shrink tubing. This will protect them from electrical shorts, and will increase the life of the device. Once the wiring is secure it's a good idea to test the Ghost 2 immobiliser.
The Ghost 2 immobiliser offers a service mode in situations where you may need to surrender your vehicle like when it is being repaired or valet-parked. This will disable the PIN sequence temporarily. Press the brake pedal, and hold the accelerator for a period of time equal to the first digit of the emergency code. The system will then enter service mode, which can be verified by flashing the indication signal 5 times.
Easy to change PIN codes
It is easy to protect your vehicle from theft by installing an immobiliser ghost 2. It is installed discreetly within the vehicle, and is only accessible with a code. The device is directly connected to the vehicle ECU via its data bus, and does not use radio frequency signals like traditional Thatcham immobilisers, or aftermarket alarm systems. This makes it difficult for thieves to hear the click of an immobiliser relay or add new keys. The control unit is concealed in the wiring harness or dashboard, and cannot be physically altered to reset the system.
The ghost 2 immobiliser is linked to the vehicle's CAN Data network. It makes use of buttons on the door panels, steering wheel and the centre console to create a programmable sequence of up to twenty button presses, which must be entered to start the engine - similar as a PIN code. This unique system can be reprogrammed and does not require wire cutting during installation. You can even start your vehicle in Service or Valet mode when you give it to a mechanic to complete the work.
You can also make use of the app to alter your PIN code, or deactivate it completely if lost your keys. This feature is especially useful when you have lent your vehicle to someone else to be used as a valet or service because it prevents them from starting your car and driving it away without consent. It's also unnoticeable by professional thieves since it doesn't make use of radio frequencies or circuit cuts.
The ability of the immobiliser stop relay thefts is a great feature. Relay theft is among the most common methods of car theft. The criminals hack your car's diagnostic ports, then alter the signal sent by the car's ECU to trick it into believing that the car's key is valid and present. This is how traditional immobilisers can be bypassed, however, with the ghost 2 immobiliser the signal is delayed before it reaches the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that safeguards your car from hacking, key-cloning and key theft. It is activated by connecting to the CAN data network in your vehicle and asking you to enter a PIN number before it will start the engine. It also prevents thieves from using signal spoofing or device spoofing, both of which are common tactics used to steal vehicles.
The system is simple to use and works like an ordinary auto alarm. Installing the system allows you to create a unique 20-digit PIN code that you must enter before starting the vehicle. This will stop your vehicle from being stolen, even when you lose your keys. You can turn off the system using an app on your smartphone.
The ghost is completely silent and does emit radio frequency signals. It is a discreet weatherproof device that can be mounted anywhere in your vehicle. It can be hidden under the dashboard, door panels or the steering wheel. It communicates with your ECU over the CAN data circuit, and is not affected by diagnostic tools that thieves employ to locate security systems. ghost immobilisers is also not affected by jamming devices that alter codes.
It is a security system that can be used to stop the theft of all vehicles. Its technology is proven to be effective and complies with TASSA standards. The Ghost is a fantastic choice for classic or sports cars. It can be used as a method to safeguard vehicles hired on websites like Turo.
The Autowatch Ghost 2 represents the next generation of vehicle immobilisers. The system is inaccessible to thieves, and prevents them from starting your car without your PIN, or unless they are authorized by the app. It does not emit radio frequencies, or any other signals scanners could detect. Installation is simple and quick. The app is simple to navigate and offers a user-friendly interface that makes it easy to configure and use. It also comes with an GPS tracker that can help police locate and recover the vehicle.
Easy to reset
It is possible to protect your vehicle from theft by using a ghost 2 immobiliser. It integrates with your vehicle's ECU to create a security barrier that thieves are unable to breach without the correct PIN. The device is also TASSA-verified which means it is recognized by insurance companies. It's an effective tool to stop car theft, and can save you a lot of money over the long term.
Contrary to traditional alarms/immobilisers which require circuit cutting for circuit cutting, the Ghost system is directly connected to the vehicles CAN data network. It works by using your existing buttons on the dashboard as well as the steering wheel. You can create a unique pin that is up 20 presses in length. This PIN has to be entered before the engine can be started like a credit card PIN. The Ghost system is invisible to thieves, and there are no LEDs to signal its presence. This makes it the most reliable aftermarket CAN-bus system available today.
The Ghost system has another benefit: it does not transmit radio frequency signals. This means it is not scanned by thieves or intercepted. This can prevent the cloning of keys and relay attacks as well as the more popular method of hacking into a car's CAN bus system by scanning for signals from the alarm/immobiliser. In addition, the Ghost system is designed to be completely hidden inside your vehicle. There aren't any lights or signals that indicate its presence.
The system also has a Transport Mode that disables the Ghost system that is helpful in situations in which you have to temporarily disable it, for instance, when you are traveling or performing maintenance. This mode isn't as effective as Service Mode as it doesn't disable the Ghost system when you exceed 31 mph within 15 minutes.
You will require the emergency code provided by your installer to reset your Ghost 2 immobiliser. It is typically hidden beneath a scratch-off section on the card that was provided with your installation. This emergency code should be secured and stored in a secure location like a wallet at home.